8 Replies Latest reply on Apr 12, 2014 5:41 PM by Jeian

    pls. help how to configure aztech dsl5001h to dlink dl-lb604 load balancer?

    vigilante888

      i just want to combine my smart mybro and globe dsl, i dont know the process to configure the aztech router. pls. help...

        • Re: pls. help how to configure aztech dsl5001h to dlink dl-lb604 load balancer?
          Jeian

          Hi!

           

          You may select automatic by clicking the wizard or use the MANUAL MODE below.

           

           

          Please connect the following internet on wan interfaces. Then configure each WAN connection based on the settings from your ISP (Internet Service Provider).

           

          Set a DHCP WAN

          1. Go to WAN

          2. Select Interface: Wan1 (For first connection)

          3. Connection Type: DHCP (For Globe Wimax and LTE, including DSL(from the modem))

          4. Apply

           

          Set a PPoE WAN

          1. Go to WAN

          2. Select Interface: Wan2 (For second connection)

          3. Connection Type: PPoE (Canopy Smart)

          4. Enter the required details

          5. Apply

           

          Opening Load Balancing Program

          1. After setting up each WAN and connecting to each other

          2. Go the Load Balance and Click Enable,

          3. Set Base: Bytes Tx + Rx

          4. Set Loading Share 50 - 50

          5. Click Apply

          • Re: pls. help how to configure aztech dsl5001h to dlink dl-lb604 load balancer?
            Jeian

            Try bridged mode .

             

            I haven't tried this multi-connection, but it seems it is the only way for it to
            work.

             

            --
            Here is an information gathered from the internet

             

            Warning: This article is a bit technical for most people.

            For those who purchased a Load Balancing Router by D-Link particularly DILB604, here is a sample setup instruction to make your purchased equipment usable and not end up in your stock room.

             

            In my example, I will be connecting a single ISP since I only have one available (pinaputol ko na yung smart bro ko a year ago to lessen my overhead expenses). I will be setting up a Globe Wired Connection to my DILB604 Router.

             

            Prerequisites for this setup:

            • You must know your username and password to access your modem’s configuration page
            • You must know your username and password to access your router’s configuration page
            • Basic knowledge in IP addressing, subnetting and networks is an advantage

             

            You need to know your device’s MAC ADDRESS from your aDSL modem-router. This information is necessary to properly configure D-link’s dual WAN router. If you can access your modem’s configuration page you will see something like this:

             

             

            So, you can either use the “DSL ” or “Ethernet” Mac Address. In my example I will be using the DSL.

             

            For those who can’t access this page, what you can do is to plug your Aztech modem directly to the PCs LAN port. You can access the property page via the control panel -> Network Connections -> Network Devices. Right click on the Network device and select properties. Select IPv4 – Internet Protocol version 4 it will be highlighted and then click properties. It will open this page:

             

             

            Make sure that you selected, the first one “obtain IP address automatically” so you can acquire the IP address provided by the Aztech Modem. Press OK. Confirm that you have an internet connection by opening your browsers and surfing to various websites. If all is well, then it’s ok to proceed to the next step.

             

            Open your command prompt (CMD), press WINDOWS KEY + R to call up the RUN command and type CMD and press OK. Once you entered the CMD or DOS, type the following command “arp -a” (without the quotes). It will return a series of mac addresses. You will see the right one with your Gateway address on it usually it ends with “1″ number e.g 192.168.1.1 (sometimes the first one on the list). The Mac address preceding this line is the MAC address of your modem. Take note and proceed to the next step.

             

            NOTE: You need to know your username  and password to access the configuration page of your router. DEFAULT is admin with no password.

             

            Access your DLink router’s web configuration page using your available browsers. (There is a need to remove the UTP cable from the AZTECH modem and plugin yout PC directly to your DLINK router using another UTP cable. After this setup you will need the modem to be plugged-in to your router) Type in sa address bar 192.168.1.1 (default – change this to avoid conflict with the AZTECH modem via HOME -> LAN -> LAN SETTINGS). It is essential also to setup the DHCP server and make sure na parehas ang IP RANGE will match with the LAN IP. So in my example, my router will have the IP192.168.0.1 and subnet mask 255.255.255.0 so it follows in my DHCP the following settings:

             

            Press APPLY and wait for a few seconds so your PC can acquire the new IP address from the router since you’ve changed the IP range. The router may restart again to apply the new settings. You may have a problem connecting to your router webpage since we modified its LAN IP. Use thenew IP Address in the address bar to access the page. In my example I have to type 192.168.0.1 instead.

             

             

            NOTE: Starting IP and Ending IP may vary starting from 192.168.0.2 – 192.168.0.254. Determine how many IP do you want your DHCP to provide for your computers.

             

            Logon again to your Dlink Router. Once you have accessed the router’s web, proceed to HOME ->WAN tab. You will see this page:

             

             

            Follow what I have put here except for the DNS part since this is optional. You can leave it blank to use the default DNS provided by your ISP. Even the HOST NAME can be ignored. This portion is used to identify the current connection you’re into.  WHAT IS ESSENTIAL HERE IS TO PUT THE CORRECT MAC ADDRESS to make it work. Then connect your Aztech modem to the DLINK Router using a LAN/UTP cable. The other end of the UTP cable from your modem should go in one of the WAN ports of your Dlink Router. In my setup, the UTP cable is plugged-in to the WAN1 port to make sure it will work. Press APPLY and wait for a few seconds, the router will reset then try to open a browser and check for connectivity. You can also access your router’s configuration page and go to STATUS PAGE. WAN1 status should state “connected” and likewise you can connect to the internet.

             

            For the 2nd ISP or WAN connection, follow the same procedure with a slight modification on WAN config part. You have to select the WAN 2 interface and input the MAC address of the 2nd ISP’s modem. You may want to turn on the Load Balancing feature by going to the HOME -> LOAD BALANCE side menu. Make sure you use load balancing based on packet Tx and Rx. Experiment on load share – try 50/50 for starters.

             

            I will try to discuss the other important settings to make your Load Balancing Router work better for you like PORT FORWARDING and QOS (quality of service).

             

            = Setting Up Your D-Link Load Balancing Router (WAN Config) | The Techie Bro =

            = http://www.jnet.cf/ =

            • Re: pls. help how to configure aztech dsl5001h to dlink dl-lb604 load balancer?
              vigilante888

              actually sir its working naman po both WAN1 & WAN2 without using bridge mode po and base on speed test, session mode seems to be best setting ... anyway po im just wondering why cant it perform like combined speed of smart mybro  canopy 1.66Mbps + smart mybro  canopy 1.66Mbps = 3.22Mbps (session mode) unlike globe dsl 3.01Mbps +  smart mybro  canopy 1.66Mbps  = unstable ping, speedtest result doenst reflect combined speed.

              tnx tnx again for reply...

                • Re: pls. help how to configure aztech dsl5001h to dlink dl-lb604 load balancer?
                  Jeian

                  I really don't know as I am new in terms of this kind of problem. Also this

                  also raises do at my own Wimax+Wimax that should give me 4mbps. Totally

                  Speedtest are not accurate in terms of dual wan as it uses 1 ip only. While

                  I prefer using testmy.net and/or Bandwidth Filtering.

                   

                  When this happen on my tomato dual wan router, I just put a bandwidth

                  allocation to each device as the minimum would be 50% of the said internet

                  connection combined and maximum as 110% of the internet connection combined.

                   

                   

                  On Sat, Apr 12, 2014 at 5:22 PM, vigilante888 <